Suzuki DRZ400 3X3 mod Videos

1096919 Says:

Nov 18, 2008 - Nice job guys. Great video!

nigel182 Says:

Nov 18, 2008 - Thanks for the nice tutorial. I brought my laptop in my garage and followed along. It worked great!

byrneiboy Says:

Nov 18, 2008 - Is this exactly the same for a 'sm' with a full yoshi?

robincx Says:

Nov 18, 2008 - I've been looking for exactly this. Thanks so much! My Yoshi and JD jet kit arrive next week, I'm stoked to have a tutor available.Thanks, great job!

neznarftruk1 Says:

Nov 18, 2008 - after i do this, will i have to continue to mess w/ the jetting?

rbrtplly Says:

Nov 18, 2008 - If you go to the web site to get the proper jets for your altidude and other mods you already have should be ok. Go to the forum and select the suzuki drz400 and search 3x3 mod you should find all the info you need. It is all free.

rbrtplly Says:

Nov 18, 2008 - The jet kit may be different but the procedure is the same.If you go to the web site to get the proper jets for your altidude and other mods you already have should be ok. Go to the forum and select the suzuki drz400 and search 3x3 mod you should find all the info you need. It is all free.

Chonchachencho Says:

Nov 18, 2008 - what is your elevation?

Chonchachencho Says:

Nov 18, 2008 - lol... oh

robincx Says:

Nov 18, 2008 - Just did it. I tried without removing the carb, but it became apparent that with the float bowl screws being so tight you have to pull it out. I did not need to unhinge the frame, just release the throttle cables and loosen the gaskets. It will come out with a little convincing.

rbrtplly Says:

Nov 18, 2008 - I am at 100 - 200 Feet.

Xmoto16 Says:

Nov 18, 2008 - narrator guy sounds like the ape from my gym partners a monkey.lol right but seriously nice job

0i0overload0i0 Says:

Nov 18, 2008 - i got a crf150r. i got a rocket slip on and i was going to do a R&D power bowl to take awey the bop

robrobrobrob888 Says:

Nov 18, 2008 - lovely thanks!

Jason85rida Says:

Nov 18, 2008 - same for the drz 400 E? thanks

jcdenton7 Says:

Nov 18, 2008 - Excellent video! This is probably the most informative video I've seen on here. I don't own a DR-Z400, but I do own an XT 225. I had to do the same thing with the plug covering the fuel mixture screw on my bike. 3 turns out is what I'm at, and it works magnificently.

STUARTHAGERMAN Says:

Nov 18, 2008 - Thank you very much for the video. It helped me out.

Duedog Says:

Nov 18, 2008 - Wow...thank you so much. This video made the whole experience a million times better than it would have likely been.Cheers!

jim6504 Says:

Nov 18, 2008 - Great video, just done the 3by3 hole, but got origanal jets, and a rase can just put on, will the jets make it go better, cos now it's not runing right, cheers for the video again

jbwiden Says:

Nov 18, 2008 - It will run lean if you just make the airbox hole larger. Get a jet kit(jd is considered the best) and then remove tape.

jbwiden Says:

Nov 18, 2008 - I meant to say cover the hole back to original size with tape and when jetting completed remove tape

rbrtplly Says:

Nov 18, 2008 - YES, Cover the hole back up with duct tape to about the original size until you get the correct jets and jet kit. You are now running lean and could do some engine damage.

KanzlerM Says:

Nov 18, 2008 - The jet kit makes a huge difference.Be careful - until you re-jet your carb you are running super lean after the 3x3 - your bike will run much hotter.The bikes already run lean when stock to pass EPA reqts; 3x3 w/o re-jetting makes them even worse.

maxilong1 Says:

Nov 18, 2008 - dude you are effing amazing, i was wondering how i was about to try to do this without much mechanical experience, this was so helpful, thanks a million

mblendinger Says:

Nov 18, 2008 - Hello! Just a question, this mod is applicable to the new DRZ400S 2009 ? or this issue was resolved from the factory on the new models ? can't found the size of airbox in later models to see if now it is bigger.... thank you!